🔥 Flаѕh Sаlе IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

Affiliate reviews IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

So you can check out the other reviews Rеvіеw Dіѕсоunt IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset at Amazon.com

only with $13.99

Operation Mode	ON-OFF-ON
Current Rating	30 Amps
Operating Voltage	250 Volts
Contact Type	Both
Connector Type	Plug In
Brand	INDUSTEC MAINTENANCE SOLUTIONS WE'RE IT WWW.INDUSTRIALTECHNICIANS.COM
Switch Type	Rocker Switch
Terminal	Pc Pin 1/4" .250" Spade
Material	Plastic, Metal
Item Dimensions LxWxH	1.75 x 1 x 1.75 inches

---

• DPDT Rating: 30 amps at 12 Volt DC and 15 Amps at 24 Volts DC. Has four prong post with built in jumper bars for Polarity Reverse. Size: This Reverse Polarity Switch with 1.47''X0.83''(37.4X21mm) Cut-out Size and 1.736''X0.95''(44.1X24.13mm) Housing Size. Three Position. Wires not included. Rubber external gasket cover under mounting lip to protect panel from dirt, dust and rain and help keep panel dry. Not waterproof. Push Button.
• This is a momentary electrical system switch used for jogging or inching operations. A DPDT switch is equivalent to two SPDT switches. Dual Operation. It routes two separate circuits, connecting each of two inputs to one of two outputs. The position of the switch determines the number of ways in which two contact can be routed. Always make sure you are using a switch and wire sufficient to handle the load you are carrying. In higher draw applications, a relay may be needed.
• Can be used to replace SWT-ROC-MOM-4W, 129-PR-MOM. Atwood Power Jack numbers: 80236, 80511, 80515, 80530, 80509, 80524. Direct Replacement for Atwood Part# 87570 and Lippert Components part number 226023. Other part numbers: KCD2-7-223-4P-X, ‎KCD2-7-223B
• Can be used to replace Drum, Rotary, Cable, Adapter, Relay. Also a great replacement for RV or Electric Trailer Power, Travel Trailers, Tongue Jack Stabilizer, Fifth Wheels Jacks, and slideout Power awning switches. Great for Travel Trailers such as: Keystone, Grand Design, and Coachman. Snap In Switch Easy install. 30A Momentary Automatic Reset action, Resetting returns to off when released. Simply connect power and ground and two DC motor leads and the switch will reverse the motor direction
• Our heavy duty switches are durable and reliable. Used in Auto, Car Accessories, Camper, Hitch, Truck, Boat, Motorcycle, ATV, UTV, Airplane, Aviation, Robotics, Automotive Parts, Automation System, Industrial, Factory, Machine Work, Marine, Do it yourself DIY Projects, Winch, LED Light Bar, Sound Systems, Awning, Bilge Pump, Dash Panel Controls, Jack Hoist Actuator, Lift, Stabilizers, Electronics, Liftgate, Motorized Windows Up / Down, Door Open / Close, Electrical Devices, and much more!

---

Product Description

• Hook any 2 side by side to supply and others to motor
• The DC motor will reverse one way then the other with switch operation
• The switch will return to center off position when released
• Great for easy fix solution for Motor Homes Boats, windows, Robotics, Kids science projects and many more.
• Used for tow winch devices in some cases
• Used on many tongue and 5th wheel jacks

Read more

IndusTec 30 Amp Momentary Motor Polarity Reverse Rocker With 12 AWG 65/30 tinned

switch amperage rating	30 Amps at 12 VDC 15 Amps at 24
Wiring Instuctions	Hook 2 center terminals to 12 or 24 volt power supply then other 2 to motor
Cut Out	Fits standard 0.83 X 1.46 Cut out About 21mm X 37mm

Seal	Has rubber rubber seal to help keep water out of panel
Action	3 Position spring return to center off position
Markings	None

	30 Amp Momentary Rocker with Pigtail leads	30 Amp Latching Rocker with Wires	30 Amp Momentary Rocker 4 pc pin	30 Amp Locking Rocker 4 Quick Conects	20 Amp resetting Rocker and wires	20 Amp Rocker 4 1/4 .250 Pins
Has 30 amp wire	✓	✓			✓
Switch rated for 30a at 12 VDC	✓	✓			✓
Will spring to off when released	✓		✓		✓	✓
Stays in last position placed when released		✓		✓
Has panel sealing gasket under lip	✓	✓	✓	✓	✓	✓

	Maintained Polarity Toggle	Momentary Polarity Toggle	10 AMP Auto Reset Polarity Toggle	10 AMP Latching Polarity Toggle	Maintained Polarity Toggle	Momentary Polarity Toggle
Has # 12 AWG 65/30 strand Tinned boat Grade Wire	✓	✓
Has 12 guage Audio Stranded Wire			✓	✓
Automatic Resetting Spring Return to Off	✓		✓			✓
Ratded for 20 Amps At 12 VDC	✓	✓			✓	✓
Rated for 10 Amps at 12 VDC			✓	✓
Silver Alloy Plated Copper Contacts	✓	✓			✓	✓

	Momentary Medium polarity Rocker	Maintained Medium Polarity Rocker	Waterproof Resetting	10 AMP Latching Reversing Rocking	IndusTec Intermediate Rocker Switch 2 Pole 2 Throw 3 Position 6 Pin	IndusTec Intermediate Rocker Switch 2 Pole 2 Throw 3 Position 6 Pin Latching
Has 12 guage Audio Stranded Wire	✓	✓	✓
Has 18 guage AWG Stranded Wire				✓
Retains Positions		✓		✓
Returns to off when released	✓		✓

	3 position auto 6 Pin	3 Position latch Pin	2 position 6 pin	2 position 6 screw	3 position 6 screw auto	2 pos SPST latch 2 screws
Latches in place		✓	✓	✓		✓
Automatically returns to Off	✓				✓
3 Positions	✓	✓			✓
2 Positions			✓	✓		✓

Switches for Dummies

To clear up voltage ratings on switches

Most manufacturers print a voltage rating on the switch at the factory. They normally print the highest voltage at which the switch should be used for on a continuous basis under normal conditions. Now this is a very controversial statement because not everyone's normal is the same. Lets just say dust and debris not visible, Moisture not high and no extreme temperatures that would affect the insulative or mechanical properties of the components.

It needs to be said here that the switch is good for any voltage below that rating all the way to zero volts. Under the same conditions no matter whose definition of normal you use. So if the connecting device says 600V on it it is also good for 12 VDC or 24 VDC or 125 VAC and 250 VAC and so on at any value between 0 and 600 AC or DC.

To clear up Amperage ratings on switches

That does not mean that the amperage rating on the switch applies to all voltages and types of current. As a matter of fact it only is supposed to apply to the voltage and type stated on the switch.

If you apply ohms law to voltage and amperage it would indicate that if the voltage were half the amperage could double. I Current (amperage) = Voltage divided by Resistance. Changing the voltage of the circuit does not change the resistance. However that is not true with alternating current. So you can not use ohms law to determine the amperage value for AC. And there are many more mechanical factors for both DC and AC that have profound affects on arching outside the scope of this discussion. Like materials,speed, pressure, sliding, bouncing, and so on. So it is very important to reach out to the manufacturer of any switch for amperage ratings for the voltage you need in the circuit.

Maintained and Momentary explained

A Maintained switch is noted several ways in different industries On Off On or Latched or Latching or Locking It is going to Latch Lock in position you or someone else places it. Used for non jogging operations like pumps fans or lights A momentary switch denoted in several ways also is (On) Off (On) or Resetting or automatic reset or springing This term means it will return spring reset to a position (usually off) when you release it. For jogging operations like lift hoist winch or door

What does Pole and Throw refer to

Consider pole to indicate the number of Isolated (individual) Inputs. Throw would be the number of outputs for each pole. Do not confuse the throws with positions. Any single throw switch can only have 2 positions On Off if you think about it. But a double throw switch can have 2 or 3 positions. If a double throw switch has 3 positions it is sometimes referred to as On Off On, and will probably have off as one of the positions. ( usually in the center ). If a double throw switch has only 2 positions then it will always have the input connected to one of the outputs and will not have an off position for all outputs at same time . This is sometimes referred to as On On.

---

Specifications for this item

Brand Name	INDUSTEC MAINTENANCE SOLUTIONS WE'RE IT WWW.INDUSTRIALTECHNICIANS.COM
Color	Black
Connector Type	Plug In
Contact Material	Silver
Contact Type	Both
Controller Type	Push Button
Current Rating	30.00 amps
Item Shape	Rectangle
Item Weight	0.882 ounces
Material	Plastic , Metal
Maximum Current	30.00 amps
Measurement System	Imperial , Metric
Mounting Type	Snap In Rectangular
Number of Items	1
Operating Voltage	250.00 volts
Operation Mode	ON-OFF-ON
Part Number	ROC2234RMPR30
Specification Met
Switch Type	Rocker Switch
Terminal Type	Pc Pin 1/4" .250" Spade
UNSPSC Code	39122200
Voltage	250.00 volts

---

----------------------------

Hеу mу brо, Mаnу thаnkѕ fоr vіѕіtіng оur Wеbѕіtе. Arе уоu сurrеntlу trуіng tо fіnd fасtѕ аbоut IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic ResetThе Gооd Nеwѕ, Rіght nоw wе'rе gіvіng bіg аѕ muсh аѕ 75% fоr реорlе whо buу IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset рrоduсtѕ thrоugh thіѕ Wеbѕіtе.Nоt јuѕt thаt, уоu'll еvеn gеt уоurѕеlf а аbѕоlutеlу frее dіѕсоunt іn thе еvеnt thаt уоu оrdеr tоdау.Thаnkѕ fоr wаtсhіng аnd рlеаѕе gіvе а thumbѕ uр.

----------------------------

Disclaimer:

Thіѕ Wеbѕіtе іѕ раrtісіраnt іn thе аmаzоn ѕеrvісеѕ llс аѕѕосіаtе рrоgrаm.I dо uѕе аffіlіаtе lіnkѕ whеn lіnkіng рrоduсtѕ іn thе Wеbѕіtе dеѕсrірtіоn.Thіѕ dоеѕ nоt аffесt уоur buуіng еxреrіеnсе оr іtеm рrісе but dоеѕ mеаn I rесеіvе а ѕmаll соmmіѕѕіоn оn іtеmѕ рurсhаѕеd uѕіng ѕuсh lіnkѕ.An аffіlіаtе аdvеrtіѕіng рrоgrаm dеѕіgnеd tо рrоvіdе а mеаnѕ fоr ѕіtеѕ tо еаrn аdvеrtіѕіng fееѕ bу lіnkіng tо wеbѕіtе аnd аmаzоn.соmWе аlѕо раrtісіраtеѕ іn аffіlіаtе рrоgrаmѕ wіth оthеr ѕіtеѕ. Wе аrе соmреnѕаtеd fоr rеfеrrіng trаffіс аnd buѕіnеѕѕ tо оthеr соmраnіеѕ.

---------------------------

price review IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

product reviews IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

Consumer Reviews IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

Professional reviews from industry experts IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

Affiliate reviews IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset

Tweet